Need a little HDS help

**Wannabe...** · 08-26-2011, 02:48 PM

So, I'm starting to play with the HDS a little bit and try to figure out how and where to do stuff.

One thing that's driving me nuts is my Side Imaging. With it running at 100' left and right, the first 30' is iluminated beautifully, but it's dark past that. Yesterday, I changed it to 50' and the last 10' is still dark. I was thinking that my transducer possibly was angled down too much, so I adjusted it on the water with no change. Thinking I may have it reversed, I adjusted it up on the water and still no change. Now confused, I rotated it in increments from 0 degrees to 180 with no change. I'm thinking I've got a setting that's giving me a weak return and not necesarily the angle of the transducer that is the problem. Any suggestions?

'Nuther deal is I noticed yesterday that my Side Imaging and Regular 2D depth readings are some 1.9' different. I was thinking that since I have a US/2 and SI transducer all ethernetted together that I really don't know which transducer is feeding which output. Where do I determine and change that? Then again, if 2D is off the front and SI is obviously off the back, there really shouldn't me that much of a difference since I don't have any depth offset calculated. The SI ducer is on the jackplate and if I had to guess, I would say there is only at most 1 foot of elevation difference and most likely in the 6" range. ??

Any thoughts or ideas on either issue would be appreciated.

Wannabe...

**frank lawhead** · 08-26-2011, 02:53 PM

My HDS7 is off the us/2 and they are always a little over a foot apart--?????

**SLAB MASTER** · 08-26-2011, 03:19 PM

Inherent in these off brand units. Try HB and the problem will go away

Rofl

**Jason Gilstrap LOWRANCE** · 08-26-2011, 04:34 PM

1. what your setting for your lss-1. I usually keep mine at 800 khz 80-100ft and contrast 72-74.

2. you can change your 2d keel set in your sonar menu options. Usually you going run deep on your TM, because it hang lower the transom transducer.

**Wannabe...** · 08-26-2011, 05:05 PM

Thanks Jason. Will check it and report back.

Wannabe...

**crappiemax** · 08-26-2011, 05:54 PM

Yeah, that contrast setting is right around what mine is set at. I get some truely amazing pictures.
I keep my side image around 3 - 4 times water depth.

If I switch my ducer to 455kz I think the contrast is set around 50 +/-

There is a post "HDS discussions and interpitations" started by Crappiegirl as you figure things out how about sharing with the rest of us.

**Cane Pole** · 08-26-2011, 07:14 PM

Let the smoke out of the transducer. Give it room to breathe. You choking it.

**crappiemax** · 08-26-2011, 08:28 PM

Originally Posted by Cane Pole

Let the smoke out of the transducer. Give it room to breathe. You choking it.

Maybe I've got to recheck that 455 setting. I haven't used it in a while. I'm over 50 my memory has faded....
What settings you using?

**Cane Pole** · 08-26-2011, 09:24 PM

Originally Posted by crappiemax

Maybe I've got to recheck that 455 setting. I haven't used it in a while. I'm over 50 my memory has faded....
What settings you using?

I change mine anytime I don't like the view. Nothing improves or gets worse if you don't push a button. I mostly use 800Kz on SI. And I use the 3X rule.

**Cane Pole** · 08-26-2011, 09:30 PM

Originally Posted by Wannabe...

So, I'm starting to play with the HDS a little bit and try to figure out how and where to do stuff.

One thing that's driving me nuts is my Side Imaging. With it running at 100' left and right, the first 30' is iluminated beautifully, but it's dark past that. Yesterday, I changed it to 50' and the last 10' is still dark. I was thinking that my transducer possibly was angled down too much, so I adjusted it on the water with no change. Thinking I may have it reversed, I adjusted it up on the water and still no change. Now confused, I rotated it in increments from 0 degrees to 180 with no change. I'm thinking I've got a setting that's giving me a weak return and not necesarily the angle of the transducer that is the problem. Any suggestions?

'Nuther deal is I noticed yesterday that my Side Imaging and Regular 2D depth readings are some 1.9' different. I was thinking that since I have a US/2 and SI transducer all ethernetted together that I really don't know which transducer is feeding which output. Where do I determine and change that? Then again, if 2D is off the front and SI is obviously off the back, there really shouldn't me that much of a difference since I don't have any depth offset calculated. The SI ducer is on the jackplate and if I had to guess, I would say there is only at most 1 foot of elevation difference and most likely in the 6" range. ??

Any thoughts or ideas on either issue would be appreciated.

Wannabe...

Structure depth reading. I believe this reading follows the soft/hard bottom area depth. Observation. Watch this reading. You have plenty of time to observe before you get your 1 fishie.

No depth offset for DI.

Thread: Need a little HDS help

Thread Tools

Display

Need a little HDS help

Posting Permissions