Likes Likes:  0
Thanks Thanks:  0
HaHa HaHa:  0
Results 1 to 10 of 10

Thread: 798 cutting out....

  1. #1
    Join Date
    May 2008
    Posts
    204
    Post Thanks / Like

    Default 798 cutting out....


    Sometimes when I start up the motor, my 798 freezes up and I have to pull it off the cradle to reset...

    any fixes out there? couldn't narrow down specifics on a search

  2. #2
    chaunc's Avatar
    chaunc is offline 2014 Crappie.com Man of the Year * Crappie.com Supporter
    Join Date
    Apr 2004
    Location
    Sharon, Pa.
    Posts
    9,696
    Post Thanks / Like

    Default

    Check battery voltage. Make sure it's at least i believe, 11.5. I think thats what Canepole told someone else.

  3. #3
    Join Date
    Apr 2004
    Location
    Wagontown, PA
    Posts
    2,233
    Post Thanks / Like

    Default

    Yes, you are getting a voltage drop when starting the motor. That's not healthy for electronics. It could be your battery's condition or state of charge, or poor wiring connections. I was getting low voltage to my electronics by powering them off my fuse panel. I ran a separate wire straight to the battery, for my electronics, and that cured the problem. Of course the separate wire still has to have a fuse in it.

  4. #4
    CatFan's Avatar
    CatFan is offline Crappie.com 2K Star General * Crappie.com Supporter
    Join Date
    Jun 2004
    Location
    SW Indiana
    Posts
    2,777
    Post Thanks / Like

    Default

    Several possibilities:

    Cranking battery is old, or is too small for your outboard. The fix is a new battery with sufficient CCA for the outboard.

    Cranking battery isn't being charged fully between trips or is being used heavily without enough outboard run time to recharge it during the day. The fix is eitherchanging charging practices, a new cranking battery with larger RC (keeping the CCA requirements in mind) or spending more time running around and less time fishing

    Bad connections in the cabling to the 798. If you are tapped in at a panel, try running the wires directly to the battery.

    Another solution is to add another battery dedicated to the electronics, along with a charger.

  5. #5
    Cane Pole's Avatar
    Cane Pole is offline Crappie.com 2011 Man of the Year * Crappie.com Supporter
    Join Date
    May 2004
    Location
    Pumphouse Tn.
    Posts
    23,940
    Post Thanks / Like

    Default

    My 997 has this problem. It freezes when cranking, but my Lowrance or Garmin doesn't. I have a new cranking battery with twice the Yamaha recommended CCA and reserves. New battery may or may not fix the problem. I just shut the unit off before cranking, then turn it back on.

    Wire the head unit direct to the battery. This may or may not help.

    I feel your pain.
    Member BS Pro-Staff and Billbob Pro-Staff
    Proud Member of Team Geezer... authorized by: billbob and "G"

  6. #6
    rnvinc's Avatar
    rnvinc is offline Crappie.com 2016 Man of the Year * Member Sponsor
    Join Date
    Sep 2008
    Location
    West Ky
    Posts
    13,291
    Post Thanks / Like

    Default

    Quote Originally Posted by Cane Pole View Post
    My 997 has this problem. It freezes when cranking, but my Lowrance or Garmin doesn't. I have a new cranking battery with twice the Yamaha recommended CCA and reserves. New battery may or may not fix the problem. I just shut the unit off before cranking, then turn it back on.

    Wire the head unit direct to the battery. This may or may not help.

    I feel your pain.
    It's hard to believe that the great CP could ever have an electrical problem...:D:D:D
    www.podunkideas.com <--Click here
    ------------—————
    https://www.crappie-gills-n-more.com/
    https://cornfieldfishinggear.com/

    ------------------------>> Pro Staff Sonar Advisor

  7. #7
    Join Date
    May 2008
    Posts
    204
    Post Thanks / Like

    Default

    I was thinking about putting in a small capacitor like the loud thumping speaker guys put on their cars to protect their stereo amps on start up from the same kind of thing...

    any thoughts?

  8. #8
    CatFan's Avatar
    CatFan is offline Crappie.com 2K Star General * Crappie.com Supporter
    Join Date
    Jun 2004
    Location
    SW Indiana
    Posts
    2,777
    Post Thanks / Like

    Default

    Quote Originally Posted by aekhoff View Post
    I was thinking about putting in a small capacitor like the loud thumping speaker guys put on their cars to protect their stereo amps on start up from the same kind of thing...

    any thoughts?
    Your unit is shutting down because it is sensing low voltage and choosing to shut down. That threshold is adjustable on Humminbirds. If your cranking battery can't hold 10.5V while it is cranking the outboard, there is a problem, and a cap isn't going to have any effect unless it is so large as to be a battery in itself. The outboard will actually draw power from such a capacitor for the microseconds that it can hold more voltage than the battery.

  9. #9
    Join Date
    Mar 2006
    Location
    Manchester, Tennessee, United States
    Posts
    1,232
    Post Thanks / Like

    Default

    Same issue with my 798. I checked the voltage and was only pulling 9 v out of the panel. I had to run straight ot the battery to get enough. What a pain.
    Secretary of Da Fish!

  10. #10
    Join Date
    Mar 2007
    Location
    bloomington, illinois
    Posts
    1,151
    Post Thanks / Like

    Default

    Don't change the under voltage settings they are there for a reason. I also have a 798 and I don't turn it on until the motor is idling. Follow the cca your outboard manual should specify the cca. Anything you can do to seperate your dc circuits used for electronics would help performance. ie. run new wires directly to your units from the battery with inline fuses or a 3 amp breaker, extra length also aids in voltage drop so running wires directly to the unit will help. tapping off of other wires that go through devices or other fuses will hamper use and could possibly damage your unit. Capacitors are basically used for help in starting but in this application the draw is coming from the motor and there is not a good way to isolate it to just aid with the 798.
    HOOKED-FISHING.COM CDC PROUD SPONSOR
    B'n'M Pro Staff
    Bobby Garland Crappie Baits Pro Staff
    Outdoor Writer

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

BACK TO TOP