Likes Likes:  0
Thanks Thanks:  0
HaHa HaHa:  0
Results 1 to 8 of 8

Thread: 40hp johnson

  1. 09-16-2012, 08:58 PM #1
    JJohnson's Avatar
    JJohnson
    JJohnson is offline Slabmaster II
    Join Date
    May 2011
    Location
    Arkansas
    Posts
    162
    Post Thanks / Like

    Default 40hp johnson


    Tilt /trim cylinder leaking any suggestions rebuild or replace.
    Reply With Quote Reply With Quote
  2. 09-17-2012, 06:32 AM #2
    arkcrappie's Avatar
    arkcrappie
    arkcrappie is offline Crappie.com 3K Star General
    Join Date
    Feb 2012
    Location
    Blytheville
    Posts
    3,186
    Post Thanks / Like

    Default

    As long as the shaft is not scarred, I'd say rebuild. I had to rebuild one on a 40 Yamaha quite a few years ago and that held up fine. Then again, if you are needing a reason to get a new motor...........
    Reply With Quote Reply With Quote
  3. 09-17-2012, 02:15 PM #3
    JJohnson's Avatar
    JJohnson
    JJohnson is offline Slabmaster II
    Join Date
    May 2011
    Location
    Arkansas
    Posts
    162
    Post Thanks / Like
    Thread Starter

    Default

    Rebuild kit almost 80$ went to John deere got square o-ring 1$ not leaking yet
    Reply With Quote Reply With Quote
  4. 09-17-2012, 03:36 PM #4
    BigRiverMarine's Avatar
    BigRiverMarine
    BigRiverMarine is offline Crappie.com Legend
    Join Date
    Feb 2010
    Location
    Arkansas
    Posts
    23,375
    Post Thanks / Like

    Default

    Quote Originally Posted by JJohnson View Post
    Rebuild kit almost 80$ went to John deere got square o-ring 1$ not leaking yet
    Yer killing our profit margin!!! BWAHAHAHAHA


    Big River Marine
    Bill Burnett
    870-635-0202

    We offer Xpress, Excel, and Alweld Boats. Yamaha, Suzuki, Evinrude, and Tohatsu/Nissan Engines.
    Pro Staff, Southern Pro Tackle and Ozark Rods.
    Member, Tri-State Crappie Anglers
    We only sell the Best. Ranger, Xpress, Yamaha, Suzuki, Tohatsu.
    Reply With Quote Reply With Quote
  5. 09-17-2012, 03:44 PM #5
    JJohnson's Avatar
    JJohnson
    JJohnson is offline Slabmaster II
    Join Date
    May 2011
    Location
    Arkansas
    Posts
    162
    Post Thanks / Like
    Thread Starter

    Default

    I'll give u a call if this don't work. thanks
    Reply With Quote Reply With Quote
  6. 09-17-2012, 06:37 PM #6
    NIMROD's Avatar
    NIMROD
    NIMROD is offline Crappie.com Legend - Kids Corner Moderator
    Join Date
    Jan 2005
    Location
    Plainview, / Russellville , Arkansas
    Posts
    17,085
    Post Thanks / Like

    Default

    Poor boys got poor ways! Glad you egineered a fix without bailing wire or duct tape.
    Moderator of Beginners n Mentoring forum
    Takeum Jigs

    Reply With Quote Reply With Quote
  7. 09-17-2012, 09:25 PM #7
    JJohnson's Avatar
    JJohnson
    JJohnson is offline Slabmaster II
    Join Date
    May 2011
    Location
    Arkansas
    Posts
    162
    Post Thanks / Like
    Thread Starter

    Default

    Yea it seems to be fine I stalled it at top and bottom several times. time will tel. thanksl
    Reply With Quote Reply With Quote
  8. 09-17-2012, 09:43 PM #8
    BigRiverMarine's Avatar
    BigRiverMarine
    BigRiverMarine is offline Crappie.com Legend
    Join Date
    Feb 2010
    Location
    Arkansas
    Posts
    23,375
    Post Thanks / Like

    Default

    I do hope it works for ya. It should!


    Big River Marine
    Bill Burnett
    870-635-0202

    We offer Xpress, Excel, and Alweld Boats. Yamaha, Suzuki, Evinrude, and Tohatsu/Nissan Engines.
    Pro Staff, Southern Pro Tackle and Ozark Rods.
    Member, Tri-State Crappie Anglers
    We only sell the Best. Ranger, Xpress, Yamaha, Suzuki, Tohatsu.
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

BACK TO TOP