Wow, big difference. Looks good.
Printable View
Wow, big difference. Looks good.
Quick picture with the Canopy frame on top. The Canopy marine vinyl fabric arrived today so I will be working on it along with the refrigerator & refrigerator hole.
Attachment 482126
After looking all over this morning for the ARP Fridge Defend controller for the camper fridge unsuccessfully I switched over the the Canvas Top for the Hog Fest Trailer. I have never sewn Weblon Regatta Marine vinyl before but it sews very nice. To walk you thru the steps to making a well fitting marine canvas it starts with a very well fitted pattern.
Attachment 482260Attachment 482261
I use house wrap to make patterns so every marine canvas I make I can make a duplicate. After getting the house wrap clamped tight to the frame I trace the finished edge onto the wrap with a sharpie.
Attachment 482262Attachment 482263Attachment 482265
After removing the pattern I lay it out on the sewing table to straighten out all the lines with a long straight edge. I also mark any obstruction to a grommet so here the center pipe would be in the way of the lacing so I X it out.
Attachment 482266
The corners need some kind of radius. Since I didn't bend the pipes but welded a square edge I have no bent radius to match so I just add something I can make the turn on with the sewing machine.
Attachment 482267
Reinforcing the edge of a marine canvas allows it to be laced on Banjo Tight. Here I'm cutting two 2in strips that will be sewn on as a reinforcement where the grommets go. Cutting it off the side of the entire roll before cutting the fabric prevents the need for piecing later.
Attachment 482269Attachment 482270
The most waterproof seam is a Double Fold Felled Seam. Here I attach the two halves with Basting Tape so they don't move while sewing. I sew the first stitch run 1-1/2 inches from the longest edge. Then baste the flap with tape before folding it over to the seam I just stitched. After folding the flap over I add another run of tape then fold the top piece over flat pressing the seam flat as I stretch it out.
Attachment 482271
My machine was a bit dry, not a lot of sewing these days so I had to stop and do a full service before running the rest of the canvas.
Attachment 482272Attachment 482273Attachment 482274Attachment 482275
The first picture I'm sewing the first stitch, the second & third I'm doing the second stitch. It only shows one stitch on top. That second stitch I try to run right down the edge of the fold as straight as possible. When sewing such a large canvas it helps to fold it so it will slide better.
Attachment 482277Attachment 482278Attachment 482279
Now I can lay the pattern on top of the piece of canvas centering the center pipe with the center seam and trace the pattern on to the canvas. I use the books as center weights and tape the edges of the pattern as flat as possible. After tracing I again straighten all the lines out before cutting out the Top.
Attachment 482280Attachment 482281Attachment 482282Attachment 482283
Now the 2 inch reinforcement strips are basted in so they don't move while sewing. I first sew the entire outside edge then baste and sew the inside edge. A Binding trim will be added to the outer edges tomorrow. I had to go look at a Yamaha F250 this afternoon the hydraulics is having issues. It's on a 33ft boat so I may be using my waders tomorrow.
Attachment 482285
Laying out the grommets takes focus, focus I don't have anymore of today so Tripletail here I come.
Amazes me all you can do. Truly an artist.
Definitely a handy man to have around
Very nice sir!
You are a man of many talents.
Somebody got some skilz goin on
Got up this morning and added a sewn on the edge binding to give the canvas a professional edge treatment.
Attachment 482302Attachment 482303
The walls in my log home reflect little light, in fact it's kinda dark. I'm lightening the photos as much as I can without totally washing them out. You can see the Binding Attachment guides the canvas while folding the Binding right before the needle. You can't install binding well without a Binding Attachment. The finished edge is nice and clean.
Attachment 482304
I did a 3 inch Grommet spacing since this trailer will be pulled on the Interstate.
Attachment 482305Attachment 482306
Using a Press-N-Snap tool with hole punch dies and #1 Grommet install dies I punch the holes and install the grommets.
Attachment 482307
Of course the canvas fits perfectly. There is no replacement for patterning a canvas job for a perfect fit every time. My hand strength is not what it used to be so the tiewraps will hold the canvas in position while I lace it with Parachute cord, tomorrow - not today. The press-N-Snap killed my hands, with the thumb troubles I'm having on both hands (the abuse never ends) I have to pick my fights these days. Lacing, you must hold tension constantly for about a hour to finish a run this long.
Curious will that stretch any over time and have to be laced again? Looks good John.