I was wondering if anybody has tried the kit from humminbird that is suppose to help with the interference from the trolling motor that shows up on a fish finder ?
Printable View
I was wondering if anybody has tried the kit from humminbird that is suppose to help with the interference from the trolling motor that shows up on a fish finder ?
They sent me the full-bore, whole hog kit, and I installed it all -
it was worth doing, for sure. And I thank Joby for helping :)
It cleared up several problems, got rid of my aerator pumps showing up
on df (interference, I mean) hid most of the cross-talk when I'm running
a Vexilar at the same time (107-400 freq) and I'm gonna say HELPED with
my original issue, troll motor interference. I can still get blue "grass"
on the screen if I'm in deeper water 15-20' or more and tm is on 20-40 percent... Can't run my sensitivity quite as high as I'd like either.
But it's plenty liveable.
I'm running MK universal sonar, so I wasn't really too surprised it didn't
completely clear up, being that close to the windings
of the motor I'm surprised it works well as it does :cool:
Yeah they sent me a box full of stuff to try..It had a new power cable and some metal rings that it said to use if you were using interlink which I am not. And they also sent me a thing that you could use as a boat anchor to go between the foot pedal and the plug on the trolling motor. It says in the directions to screw it to the floor....NOT... I am not putting that thing in the front floor of my boat !! I think i may order me a Lowrance and give it a try.. Thanks for the reply...
Its been reported that people have been able to eliminate interference by running a seperate ground wire to the TM's motor casing. You might try a temp wire and see if that helps. Run it from the TM's plug to the motor's housing.
My kit ain't showed up yet. Then again, my boat ain't showed up yet either..:(Quote:
Originally Posted by ky-slabseeker
They both a coming sooner or later.
Quote:And they also sent me a thing that you could use as a boat anchor to go between the foot pedal and the plug on the trolling motor. It says in the directions to screw it to the floor....NOT... I am not putting that thing in the front floor of my boat !!
My troller is a Minn Kota and that big resistor fits right up inside the housing under the foot pedal. Depending on your brand troller you might look to see if it will fit. It's like the hole was made for it.
The quality of the SI was awful until HB sent the kit and how it's like HD TV.
Best of luck
My kit showed up in a couple of days from the time I called them.Quote:
Originally Posted by Cane Pole
I talked to them a couple of says ago and they said stuff was on back order. Must be sending lots of kits out.Quote:
Originally Posted by ky-slabseeker
Also asked about the slow refresh and at that time they had no fix. 3 days ago.
I also got the same answer in email. I am persistent.
I have a 957 and a997 don't seem to have any interference when I run the 200 freq. but if I change to the dual freq then I get a good bit of interference....is this what ya'll are talking about or do you have it all the time?
Hey IBNFSHN I tried what you said and it worked great. It looks like it has taken 95% of the interference out. Thanks for the tip !!!Quote:
Originally Posted by IBNFSHN
Yes Sir, now that you mention it, my blue grass seems to only growQuote:
Originally Posted by AUTiger
when I've got the 83 freq. on - I usually run both beams.
IBNFSHN, thanks - have to give that a try soon.
Is anyone else having the problems that me and JWhite or did you have the problems and got them fixed??? I'd like to run both freq but not sure how to stop the interference????
I have the same noise, etc. My HB care package came in today. I will be installing it sooner or later. That one part looks like a hemorrhoid donut.:oQuote:
Originally Posted by AUTiger
Big.
You talkin about the tm choke CP? Just curious if yours is like the oneQuote:
Originally Posted by Cane Pole
they sent me... the pics in the instructions they sent out were of just
a donut with wires wrapped round n round, but the actual part they sent
was "potted" inside a neat lil black case, can't see the wires :confused:
looked like maybe a new and improved version compared to the pics.
I'm also having problems, particularly with my bow mount 917 hooked to the US2 on my trolling motor. I emailed HB, but haven't received an answer. The depth reading goes wild and the screen is generally screwed up.
I must say that after using my SI for two trips and ready to send it back and get a refund, HB said I had a trolling motor issue. After I installed their kit I have a perfect picture. I really only use it on the bow so without the kit it was useless.
I would have been better off using the Bahamian depthfinder. A 5 gallon bucket with the bottom replaced with 3/4" clear plastic. Our water isn't clear enough for the bucket fishfinder.
LOL