Printable View
I just purchased a high dollar crappie rod. Very high quality. This particular rod is 7'4" Light action. I really like the rod but it comes with Micro Guides. I'm not sure I like the Micro Guides.
Anyone have Pros & Cons when it comes to Micro Guides?
for straight down dipping they work fine , not as good for some other presentations though ....my thoughts
Quote:
Originally Posted by Ketchn
What he said!
Micro guides work pretty good if casting and retrieving, or single pole jigging. However, not so good if your slip corking. Bobber stops of any size will snag on the guides.
I like them okay. Seem to keep some of the wind knots out of light braid
Hate em. I stripped all my micro guide rods and put normal small #5 guides on them. One day with cotton on the water was enough for me to hate them.
Sent from my SM-A516U using Crappie.com mobile app
I use em a lot on the rods with small braid. I don’t like em for use with mono. On the long rods like my BGJP’s I don’t think they’re much of an issue. Ultra light rods with small braid they really shine IMHO. On those rods I like em for keeping the weight down on the tip section. Some of my rods I’ve built I use the stainless guides in a more progressive decrease I. Size and they work great with mono. Hope this helps some.
Great until they’re not!!!
Might be the braid that’s more frustrating but hard not to use.
Terrible with slip floats and line wrap at the tip frequently. Never have issues with rods like my G Loomis but these rods with micro guides are tons of fun.
Thanks for the replies. This is what I have done. Would like some comments.
I loaded my new Dobyns 7'4" Light action with Daiwa J-Braid X8. I can shoot a 1/16 jig out of sight with it.
I really like this setup but I have to use 00 fast snaps in order to have the loop. This is hard on old eyes. If I break off, I'm out of luck. Just can't re-tie while on the water. I wish someone would come up with an easy loop knot for Braid.
This setup is great but I still use mono 4# on my 4 TFO rods. I'm thinking about putting braid on all my rods.
What do you think?
Life is too short to use line you cannot see. Enjoy the time on the water, not frustration. No time have i ever thought i needed braid over mono for crappie fishing. In fact, i use hi viz yellow or orange mono on almost all of my rodsQuote:
Originally Posted by Don G
Sent from my SM-A516U using Crappie.com mobile app
I use braid because I almost exclusively shoot docks. If I still open water fished or fished with minnows, jig under a float. I would still use mono
Ive transitioned to using mono for my dock fishin recently. I was getting bad spots in the braid, and breaking off fish swinging them in the boat or if they wrapped a pole. It took me a while to realize i fish zebra mussel lakes/river and the tiny little baby ones attached to the poles and supports were fraying my line over time. Tried leaders for a bit and it helped. Now the last 2 years ive been using fresh 4lb mono so i can still shoot/flip/skip accurately and almost all of my problems have gone away, and its much easier to see the frays in the line now. I have broken off a few big fish that wrapped me up good, but i cant shoot 6lb mono well enough with 1/32 and 1/16. I respool my dock rods probably 10 times per summer to keep the accuracy.Quote:
Originally Posted by DockShootinJack
I have probably 15 other rods with braid, for walleye, bass, pike, cats, and even a couple 2lb braid for casting small jigs for bluegill.
Sent from my SM-A516U using Crappie.com mobile app
No zebra muscles here yet. Fisher the Gulf a lot in my younger years. Barnacles were the curse of any pier fishers existence
Some very interesting replies to think about. Learning something every day.
Going tomorrow and hopefully will come to some solution.
I am basically a Dock shooter and brush fisherman:
My equipment for tomorrow:
Dobyns 7'4" Light action with braid
TFO 6' UL with braid
2- TFO 6' UL with 4# Viscous
TFO 6' UL with slip cork 4# Viscous
I SI and 2D until I find fish and then verify with Garmin LVS 34. I do not watch the screen all day just for verification.
I believe you need to visit me so I can try 'em out.
Sent from my SM-A526U1 using Crappie.com mobile app
That would be great. We are going to have to do that. Is the 1 stop service station at the lake still in business.? Buy jigs and eat breakfast while your vehicle is gassed up and windshield cleaned.Quote:
Originally Posted by Cane Pole
Look up some of Fuji's slow mo vids...their nomenclature is "reduction train". You won't outcast straight line distance (controlled setup) Any rod I've built in the last 5 years, that's whats wrapped on em.
All of my rods are out of Japan. All the ones I use are made to be extremely sensitive and have micro guides. I mean real micro guides with inner diameter of 1mm. The closer the line to the blank the more sensitive the rod. And that’s not me saying that but some of the best rod builders in the world. Many of those rods are designed to be used with certain line types. I have several rods deigned for Ester lines, which have a diameter of around 0.095mm. So none of my rods will work with slip bobbers. All I do is cast and retrieve so the micro guides are no hinderance to me. I can fling a 1 gram jig a long way with these rods. When I use Ester lines I also use a shock leader tied with a 3 turn surgeons knot and it doesn’t decrease casting distance enough to really concern me. My only drawback with these tiny guides is as I have aged since I started buying these rods threading line through the guides takes me a little longer. They’re just hard to focus on in my senior years.
Regards
Sent from my iPhone using Crappie.com
All my poles have big holes. Most came from Grizzly Jigs and Richard Williams.
Sent from my SM-A526U1 using Crappie.com mobile app
Tom, at our age we NEED those BIG holes, it's too hard to see those little ones!! :RoflQuote:
Originally Posted by Cane Pole