Going to try something new !

With all the talk with all you guys pulling crankbaits. I'm going to give it a try. I am a jig fisher or float & minnow guy. But am going to give this a shot. It could end up being a disaster. I am pretty much a handyman so I am trying to keep cost down & building me own rod holders. I ordered a few pico cranks to get started. I'm wondering how I tell what speed I need to be going to pulling these & how much line I want out. I know locally Cevans seems to be a pro at this. I know this can get expensive to get into but what can't these days. Thanks for any help.

Sent from my SM-S908U using Crappie.com Fishing mobile app

Look forward to seeing the finished rod holders

I usually start at about 1.6 mph. Bandit has chart online with line length and depths, Picos run a little deeper than the 300 series Bandits. Hope this helps. Pulling cranks is my favorite way to fish for crappies.


Sent from my iPad using Crappie.com

This time of the year, I would pull at 1.6 to 1.9 mph….no more than 2.0…for a starter…keep the rod tips about a ft to 1.5 above the water…If you don’t have line counter reels out…start with about 40’ of line out..and you should be running 8-9’ deep…I would try and stay in 10’ to 14’ of water running flats or near points and creek channels…or along deep water banks out where you might. see fish on your electronics…If you find bait balls..run thru them as crappie might be feeding off them. If you have stump beds or standing timber…don’t be afraid to run the edges. If you get hung up..just reel in all lines and and backtrack to the hung up bait and you will find most times you might get your crank back. I don’t loose many. If seeing fish on electronics…your electronics will give you depths the baits need to run also. As summer progresses and water warms..stay above thermoclines if you see them on electronics.

Watch your rod tips..you will be able to tell if your crank is digging into the bottom to reel line in and raise the bait. Try different depths till you find active fish also.

Attachment 429104 Attachment 429105

The second chart is for pushing from front of boat using 2 or 3 oz line weight 3’ above crankbait if you learn to push using same speeds and depths. I use 3 oz weights.

I use 10 and sometimes 20 lb test yellow power pro braid on my Okuma DX 20 line counter reels also..

Thanks for the info!

Make a 2 or 3 ounce crank knocker. Saves the wallet a little.

Sent from my SM-A326U using Crappie.com Fishing mobile app

That's alot of info for me to remember. Man I think jig fish is alot easier. Lol ! Let me clarify one thing I'm not really making my rod holders. I'm making the bar to hold the rod holders. I have some rod holders from a pontoon I used to have I'm going to try & use for now.
Trying not to get to much money wrapped up in this all up front. My crankbaits arrived in mail today from pico. Man they get things out quick. They sure do look like good quality. Now if I can just get a day when I don't have much boat traffic in the next week or so to give this a try.

Thanks guys for all the feed back !!!
I'm sure this will be an experience for me.

Sent from my SM-S908U using Crappie.com Fishing mobile app

I got my rod holder bar mounted today. I made it easy removable. My rod holders will bolt on top of this & be able to slid anywhere on the bar. Attachment 429178Attachment 429179

Sent from my SM-S908U using Crappie.com Fishing mobile app

Looks like you have a plan.

I too am going to try and do some pulling but probably more beetlespins and curly tail jigs to start and I have 3 rodholders on back of my toon and will put two more on outsides and that's enough to start. But still I am a single pole jigger who lives for the thump primarily and can still jig the docks and have success so we shall see.

Bymo and I have pulled cranks a few times with some success on his last boat but it wasn't my favorite way o ketchn.

But have seen the incredible success robbie and his dad have had at Mark twain and how they were rigged so it is out there for us to pursue.

Quote:

---

Originally Posted by Curlytail

With all the talk with all you guys pulling crankbaits. I'm going to give it a try. I am a jig fisher or float & minnow guy. But am going to give this a shot. It could end up being a disaster. I am pretty much a handyman so I am trying to keep cost down & building me own rod holders. I ordered a few pico cranks to get started. I'm wondering how I tell what speed I need to be going to pulling these & how much line I want out. I know locally Cevans seems to be a pro at this. I know this can get expensive to get into but what can't these days. Thanks for any help.

Sent from my SM-S908U using Crappie.com Fishing mobile app

---

Like yourself I am also about to venture into pushing cranks for crappies. And like yourself, I’ve always enjoyed Working a jig for them while drifting. You and I are fortunate to have knowledgeable anglers a.k.a. crappie specialist, share their information with us. A willingness to share knowledge is The true measure of what constitutes being a great fisherman, IMHO. If you wanna learn anything about crappie fishing this website has no equal where educational value is concerned.

Have a big pair of forceps or long nose pliers handy, so you can get the hooks out quick and get back to watching rods !!

If you're fishing a lake where 2lb fish are common, a long handled net with rubberized netting sure comes in handy.