We made up some ice blades today they are three-quarter inch.
Attachment 415773
Printable View
We made up some ice blades today they are three-quarter inch.
Attachment 415773
Looks good Bob. What weight, what size hook. What does the back side look like? Can you move that dot down to the bottom of the bait?
Nice!
Good looking bait Bob. I will send a PM on payday.
Well done my friend. I started off making "Pinmins" over 50 years ago in Akron Ohio. I learned the technique from Jack Manda who owned a bait shop on Portage Lakes. I supplied his shop with "Pinmins" which stood for Pin Minnows for about a dozen years. That is what we called Ice blades back then. Folks, they are great in hard water and also soft water. Lately, I have also been soldering ice blades too, but in a different style so you can tie some Marabou on them. Here is a photo. Just solder a #6 jig hook to the small shell Snake River. It will make the ice blade like a glider action. Weight will be about 1/64th ounce. The white yarn wrap represents a wax worm and the marabou gives it action. It also holds "Slab Sauce" quite well.
Attachment 415813
Attachment 415814
Mike
I bet those will catch some.
Sent from my iPhone using Crappie.com
What other colors are you going to make Bob?
Mike where are getting your long shank gold hooks to fit a regular ice blade Number size 6 in 4. Another question on the size of Willow leaf blades would a number 3 be about an inch and a half .
Soldering a jig hook to a regular Colorado blade does that wobble when you jig it.
Thanks Bob. When do you expect to add them to your website?
I am using powder paint. After you solder the ice jig while it is warm, hold the ice jig over the powder paint jar and spoon your color(s) on with the tip of a butter knife. Shake off excess powder paint back into the jar. Continue to hold the ice jig with the forceps. Lightly touch the back of the ice jig with your soldering iron for two seconds at a time and then remove the jig from touching the soldering iron. Repeat this process two seconds at a time. You will see the paint begin to melt. That is when you immediately stop the process. Remove the jig from the forceps and see it aside to cool and dry.
I only make my ice jigs one at a time through the entire process.
Mike
Bob, I like the new colors. Looking forward to seeing how they turn out with your upcoming improvements!
Be working today on a different heat source for my powder paint trying to make the paint look a little bit better on the blade we thought about going to airbrushing but that’s another whole ball game of buying a little compressor in a little spraygun but it would be cool because we could use it on our plastics also.
I would think using a heavy duty soldering gun would get it hot enough and retain enough heat to powder paint after soldering. I have two the pencil style and then an actual gun and that gun will glow red hot!
https://www.crappie.com/crappie/diy-...teardrop-lure/
I will be working with the heat gun today before I was working with an alcohol lamp you have to be super careful alcohol lamps are very hot flame and you have to stay above the flame a little bit but I still don’t like it because I can’t get the paint to even out the powder paint so will be working with that today in the shop
As I promised we were working with a Wagner heat gun and we set the temperature for 450° that was the ticket . The alcohol lamp that I was using it was way too hot and you could not control the temperature as you can with the gun I have an closed a picture you can see the difference from the ones I previously done.
Attachment 415988
Here are some more ice blades I did today
Attachment 416020
Very nice Bob!
Those look great bob!
Sent from my iPhone using Crappie.com Fishing mobile app
You are so correct! That is what I use. I AM shipahoy 41 and I APPROVE of this message! I have been soldering ice jigs well over 55 years and you just have to take your time on each one. When I am soldering the Ice blade is held with forceps to keep it stable and in place while soldering. The moment I see the solder begin to solidify is when you hold it over the jar of powder paint and use a butter knife or small spoon to spoon it on the warm ice jig. The powder paint will begin to melt then.
Attachment 416104
Attachment 416852
Ice blades worAttachment 416852work! Thanks Bob.
Thank you for sharing i’m glad you’re working out for you.
looks great