Location of AS GPS HS puck

Anticipate the heralded arrival of the new antenna. YouTube has several videos and most mention placing the puck away from any item that could cause an interference issue like large pieces of metal (trolling motor) or electrical interference like electronics. Some suggest placing the puck on the aft end. I would prefer placing it on the bow on the opposite corner of the trolling motor. Assuming I check the position first (duct tape or other temp mounting) by checking the north orientation is there any other issue I need to watch. I have finally gotten over my aversion to drilling holes in my boat but I would rather my placement be the first and last position.


Sent from my iPad using Crappie.com Fishing mobile app

If this puck will be used with the console unit I highly recommend mounting the puck on the back of the boat, as close as you can get it to being above the transducer.... but not get interference from the motor. This will provide you the most accurate marking of waypoints and easiest navigating to a marked waypoint. Check location you want to mount it to with a compass. Move the compass around the area... if the needle moves.... try another spot. Duct tape works good to temp mount it and adjust position.

On your unit select to display your readout boxes on the side of your screen. Change 2 of those boxes to "COG" and "Heading". Then drive around and watch those two numbers. Your goal is to adjust the direction of the arrow on the puck so that those two boxes read really close to the same number while moving. Watch the video below...

https://youtu.be/Inr-y8Pe_cM?t=4

** restart the video if is starts in the middle.

Great video and I had already watched it before this posting. I will watch it with due diligence the next time. This antenna is for the Helix 10 mounted on a RAM mount on the bow. Helix 10 transducer is mounted on the Ulterra Trolling Motor hence my desire to mount the puck on the bow. I will acquire a compass to test the location then truly test it per the video before mounting it permanently. Thanks for the input and taking the time to craft such a complete post.


Sent from my iPad using Crappie.com

I actually had good luck mounting my bow AS GPS HS on the deck by the trolling motor pedal. I wanted to put it up on the front fiberglass, but I could not find a spot that did not show interference with a compass there. It sure is great with a bow unit though when fishing off shore structure/waypoints. Also take advantage of the "casting rings" or "proximity flags" features to really help pinpoint things.

I will look into that and thanks.


Sent from my iPad using Crappie.com

Ok-AS GPS HS antenna came in last night. As my transducer is mounted on my Ulterra trolling motor I want to mount it on the bow. I actually did not get any obvious interference with the hand held compass even closer to the bow light (yes-I turned it on, as well) and the trolling motor. I picked a spot that I feel is close enough to the transducer, away from stumbling over it, and where I already had a penetration hole in the bow that I will have to enlarge. Here is a pic. Of course I will tape it down for several runs but what do you think about my proposed placement? Thanks so much for taking the time to post your comments.Attachment 275117


Sent from my iPad using Crappie.com Fishing mobile app

Of course that would work ...
-----

Another option is to sandwich a plate between the gimbal mount and the ram mount for the AS GPS HS antenna ...

Attachment 275120

Rickie

Wow! Now that would be sweet. I assume I need to fabricate something or is something like that available on the market? If not, what materials should I consider? You are absolutely a fount of knowledge and great ideas!


Sent from my iPad using Crappie.com

On the fishing electronics and photography there is a post from NIMROD about the same thing. Two of Rickie's units are posted along with mine. As I wanted the puck right on top of my ducer. I remove my T/M when not in use, as the boat is stored outside for all to see.

Quote:

---

Originally Posted by dhaire

Wow! Now that would be sweet. I assume I need to fabricate something or is something like that available on the market? If not, what materials should I consider? You are absolutely a fount of knowledge and great ideas!

---

Plastic cutting board from Walmart has good weather resistant properties ...

And it's easy to work with ...

Rickie

Quote:

---

Originally Posted by tahoe 50

On the fishing electronics and photography there is a post from NIMROD about the same thing. Two of Rickie's units are posted along with mine. As I wanted the puck right on top of my ducer. I remove my T/M when not in use, as the boat is stored outside for all to see.

---

I searched but could not find that photo or post. I saw NIMROD’s reply about the location and a photo on Da Ducer. I will continue trying, and thanks.


Sent from my iPad using Crappie.com Fishing mobile app

Ok-so a bit amateur-ish but I tried to emulate Rickie’s excellent suggestion. I have the puck duct taped to the plastic board I fabricated and ready to test tomorrow. Trying to figure out how to display the screen settings that akaslyguy has in his post. Back to the book. Thanks everyone.
Attachment 275332Attachment 275333Attachment 275334


Sent from my iPad using Crappie.com Fishing mobile app

You have to change your screen settings from "overlay" to "boxes. Then change 2 of the boxes to what you want them to read. I think the guy in the video shows how to do that too.

Watched video while on boat park in the driveway. Finally got the correct sequence although my Helix 10 has some different screens. Will do the on water check tomorrow. Thanks for hanging in there with me.


Sent from my iPad using Crappie.com

Wow! Got on the water this morning and fished to daybreak. Caught several whites and a black. When leaving I went to boxes and the Sonar screen. What a great first location! Two degrees off, at the most, while idling 4 mph. Very small variation over 200 yards. Blessed with no winds, no wakeboard boats, and glass like water so I felt it was mounted in an excellent position. The trolling motor and Helix 10 did not affect it whatsoever. Screwed two mounting screws in to make it permanent when I got home. I can always loosen the RAM mount if I need to adjust it. Thanks Ricky for great suggestions and akaslyguy for such a helpful video and comments. What a great app here at Crappie.com!


Sent from my iPad using Crappie.com