Printable View
Well I did it... I pinched the transducer cable in the terrova (helix 10 si di). I've never used the US2 2d sonar that is built in to the terrova.
Trying to determine if I need additional parts to plum up the internal sonar/cable to the helix until I get a new transducer on?
You will need the Minn Kota to 7pin adapter cable ...
http://www.minnkotamotors.com/Produc...ABLE-HB-7-PIN/
Rickie
You should also shut off the DI transmitter in the HELIX DI by setting the "Connected Transducer" menu to "Dual Beam" under the Sonar tab in the Main Menu System ...
Rickie
Thank you. I'm glad you mentioned that. I called hbird customer service to ask if there was harm in running the helix si on the us2.
I mentioned the HELIX DI in my last post and I see your unit is the HELIX SI ...Quote:
Originally Posted by Jerry L
The "Connected Transducer" selection would still be "Dual Beam" to shut off the SI transmitter ...
It's under the Sonar tab ...
Rickie
I have a HB 598 SI that I broke the cable about 4' from transducer. Had nothing to loss so cut cable and run it on teroovia ran it in grove and spliced it and taped it to shaft. Not a pro job but it works and the cable is now out of the way!!!!
Maybe too late now but if you want to mount another transducer to the Terrova look at the top for Terrova transducer mount. I did mine and it looks and works great. No more pinched or cable in the way.
What is the purpose of turning off the transmitter besides gaining a few milliseconds in the processor execution time?
HB recommends not transmitting to an open channel that has no piezo at the end of that wire channel ...Quote:
Originally Posted by Cane Pole
I have yet to hear (or read) of actual damage to a transmitter or other hardware by transmitting to an open channel ...
But it's not difficult to turn it off ...so I advise this just in case ...(and to abide by HB warranty possible issues) ...
Rickie
Any circuit that generates a signal depends on the emitter - in this case a transducer - to complete the circuit. The setup of the circuit depends on the load completing it. Sort of like an outboard with its prop out of water, the engine has a tendency to overrun when this happens. Some transmitters have what is referred to as a fold-back safety which will cut the output power when there is no load. Even if this is available it is advisable to "turn off" the specific output of a generating circuit when the load is not present.Quote:
Originally Posted by rnvinc
In RF (radio frequency) we add a Dummy Load which simulates the output circuit load when we tune up a transmitter or amplifier when the actual load (usually an antenna) is not available or recommended.
de W5CPT - amateur radio callsign
I thought about that. It is pinched in a weird place. I thougt about cutting it and trying to resplice everything. I have a replacement on the way but will take a closer look at this when I get it out.
Did you twist and tape each connection or solder each one and tape it?
When you have time would it be possible to email some pictures showing where you have it routed and secured?
[email protected]
Quote:
Originally Posted by minnowtime
Thanks Rickie! That was my fault. I listed the incorrect model number/description. I do appreciate the information. I thought I had read somewhere or assumed that a person should shut that side of the transmission off but I was having trouble gathering that specific instruction from HB. The rep was pleasant but seemed rushed to get me off the phone...
Thanks again!
Quote:
Originally Posted by rnvinc
If cable is short you could splice next to the trolling motor so you could have space to water proof the cable as it will be below water level. I would try just about anything to get cable into shaft groove. Love mine with cable confined.
Yes, it works great in the groove. If I had been paying closer attention to the adjustable collar (keeping it tightened so it wouldn't slide up) all would still be good. Not sure if anyone else has trouble with it sliding up to the head? I'm going to install a hose clamp on top of the collar to make sure it doesn't slide up and pinch it again, unless someone has found a better solution?
Quote:
Originally Posted by minnowtime