Printable View
I just bought an i-pilot for my Tracker 175 that already has a Motor Guide on it. To remove the Motor Guide mount, is there nuts underneath the deck? I have a long rod storage box in the middle of the bow - but I won't be able to fit in it to access the bolts!!!!! Any idea how the Motor Guide is mounted? Thanks for your help.
I would guess nuts underneath. My question is if you can't get to them, how are you gonna get your new one mounted.
You should rubber screw holders in the mount going into the hull. This is if it was factory installed. The rubber grumets squeeze up when the screw is tighten down.. The holds should match up on your new mount but you might want to replace the grumets.
If you need anymore info, you might check with Sir WB.
You r right holic, that is how mine was but my v2 holes didn't line up with them.
Yep, them holes ain't gonna line up. If you get lucky, you'll be able to re-use 1 set, but that will be it.
Here's the nuts Hollic was talking about....have my Terrova mounted with em and have worked well. Basically, it's a brass set of threads on the end. As you tighten them up, it' expands the rubber on the sleeve and grips the hole. One word of caution, it's hard to tighten them up enough due to the give in the rubber. For your first 3 or 4 trips out, be sure to check them again. I had 2 that tried to back out on me. One added benefit is the motor will rest on a rubber pad isolating any vibration and preventing scuffs to the hull...then again, it's a smal gap and collects dust and dirt under there bad that is hard to clean if you're a neat freak. One other bad thing is it takes a honking hole to put 'em through...something like 1/4 inch or larger if I remember correctly and may not.
I think I have the MinnKota version of these nuts, but may have been MGs.
annetteshockey : MotorGuide Trolling motor mounting kit - Isolators
Wannabe...
Okay fellas - I knew someone here on the MS forum would know! It was factory installed, so it shouldn't be too bad. I didn't think about removal/installation when I ordered the i-pilot. Thanks again!
Here's a better pic and cheaper price too.
Amazon.com: Motorguide MGA015PB6 MOUNT KIT BOLTS @ 2 MOTORGUIDE MOUNT ACCESSORIES: Sports & Outdoors
Wannabe...
Perfect thanks! Should I apply lots of silicone while I am at it?
Did a little more research....was thinking Minn Kota has a similar deal, but all I found was what they call "Quick Nuts"...I've seen these on boats before.....total crap...DO NOT USE THESE!!!!!!!
MKR-8 Quick Nuts
Wannabe...
Silicone the old holes, but the rubber will make an excellent seal on the new ones so I wouldn't worry about them.....now, when I say silicone...what I really mean is marine sealant...specifically 3M 5200, which is permanent and non-removable...don't use some junk you fixed the bath tub with last year. Also, if you decide to silicone the new holes (which I wouldn't) don't use the 5200 for that, use 4200, which is less permanent and can be removed with a bunch of elbow grease.
One last thing...I don't know what's under that metal on your hull, but I hope there's some sort of backer board....If not, I'd want something under there to spread the load and prevent some metal fatigue on that aluminum deck....that would be a whole new ball of wax if you have limited access, but you need something. The Terrova is a honker with a small mount so there's a lot of stress on the mounting holes.
Wannabe...
Thanks for the input! I'll do it.
If you wish to go a extra mile, fill your holes with silicone and then place a piece of rubber insulation the length of the bracket and then bolt it down. The insulation will absorb the noice and break up interference.
This sounds like a winner.Quote:
Originally Posted by crappiholic
With the isolaters we're talking about, it's not going to be a clean installation with that rubber backing since the top of them have a rubber boot around the hole (they stick up past the top of the hull about 1/4" ) and will serve a similar purpose to the backing, but if you do that, make sure the rubber backing is UV stabilized.
Wannabe...
I also ordered one of those Minn Kota quick release mounts for installation - don't want it stolen when I go on road trips. Put the rubber insulation under the quick release mount prior to bolting down? Thanks again.
I don't mean to hijack, but I've got one of those quick release mounts I am not going to use... I'm sure you wish you had known, I do too...
What you want for it EZ?
Seems like I paid bout $85 for it, now it has dust on it and one missing nut and washer.. I'm sure whatever it is, we'll both be happy. PM me and I bet we can work it out..