Co-Pilot Remote Battery - Please Help!

Need Some Help, Please.

I replaced the battery in my C-Pilot remote about a month ago, well that battery went dead, I guess, so I put in a new one. That one lasted exactly two trips! Went by the battery barn here in good old Petersburg, VA today to get another new one, the previous two were off the drug store shelf, anyway, the guy checks it out.

He says yep, bad battery, only putting out 3V. I ask what should it be, his reply was 3.29 to 3.3. I am thinking yeah right, that little difference don't mean squat, at least to me!:eek::D

Can that small difference in voltage render the remote useless? My next question is should I have "re-rembered" (or whatever it's called) the remote to the receiver? And if so, how, as I do not remember how I did it orginally 5 years ago and I cannot find the instructions.

Thanks in Advance - Howard V.

10% below the rated voltage (3v) is considered dead. Maybe not be synced up tx/rx. Hold reset button in for 5 seconds then press any button on remote.

I disconnected my Copilot cause it would not stop chirping. Driving me crazy.
This happened Saturday. Foot control only goes left, no right. PIA.

Quote:

---

Originally Posted by Cane Pole

10% below the rated voltage (3v) is considered dead. Maybe not be synced up tx/rx. Hold reset button in for 5 seconds then press any button on remote.

I disconnected my Copilot cause it would not stop chirping. Driving me crazy.
This happened Saturday. Foot control only goes left, no right. PIA.

---

Thanks Tom - I will try the re-sync thing and hopefully be back in action.

I agree that the foot peddle is indeed a big PAIN!:mad:

Thanks Again!:D

The new battery is in the remote, I pressed the reset button for 5 seconds, it was giving a continuous beep. The remote did not work. I am wondering if the remote may be bad????

Quote:

---

Originally Posted by Rapprunner

The new battery is in the remote, I pressed the reset button for 5 seconds, it was giving a continuous beep. The remote did not work. I am wondering if the remote may be bad????

---

Sounds like it. It should have beeped 4 times after reset. But it could be either unit. Is your circuit board in correctly ? You can reverse this board and it won't work. I know.:o Can you borrow one from a neighbor and try it?

I found the manual (pdf). PM me your email and I will send it to you.

Tom

Quote:

---

Originally Posted by Cane Pole

Sounds like it. It should have beeped 4 times after reset. But it could be either unit. Is your circuit board in correctly ? You can reverse this board and it won't work. I know.:o Can you borrow one from a neighbor and try it?

I found the manual (pdf). PM me your email and I will send it to you.

Tom

---

Thanks Tom. I will have to check the circuit board as the fellow at the battery place put the remote back together, I didn't. That could be the cause, I will let you know. If the board is in correctly I will get Ranger690's remote and try that one.

If anything has gone bad I sure it is the remote and not the reciver part on the motor, I would rather spend $50.00 for a nerw remote as opposed to ~$150.00 to $200.00 for a new unit. Or, I guess I could it repaired.

Need to figure out which one is the culprit first.

Thanks Again - Will send PM.

Regards, Howard V.

Quote:

---

Originally Posted by Rapprunner

Thanks Tom. I will have to check the circuit board as the fellow at the battery place put the remote back together, I didn't. That could be the cause, I will let you know. If the board is in correctly I will get Ranger690's remote and try that one.

If anything has gone bad I sure it is the remote and not the reciver part on the motor, I would rather spend $50.00 for a nerw remote as opposed to ~$150.00 to $200.00 for a new unit. Or, I guess I could it repaired.

Need to figure out which one is the culprit first.

Thanks Again - Will send PM.

Regards, Howard V.

---

Rapstar... just try your remote on Dayton's unit.

Quote:

---

Originally Posted by PaddleFishing

Rapstar... just try your remote on Dayton's unit.

---

Gonna give that a try this afternoon. I checked my remote, the battery and board were both correctly installed. Will try using it on Ranger's and see what happens. More to follow!:D

Quote:

---

Originally Posted by Cane Pole

10% below the rated voltage (3v) is considered dead. Maybe not be synced up tx/rx. Hold reset button in for 5 seconds then press any button on remote.

I disconnected my Copilot cause it would not stop chirping. Driving me crazy.
This happened Saturday. Foot control only goes left, no right. PIA.

---

You no you can turn the chirping off you have three settings!!

Quote:

---

Originally Posted by OsoFishy

You no you can turn the chirping off you have three settings!!

---

Please elaborate. What are the three settings and how does one change them?

Thanks!:D

Quote:

---

Originally Posted by Rapprunner

Please elaborate. What are the three settings and how does one change them?

Thanks!:D

---

Hold the top two buttons (increase and decrease speeds) for one second. If you hear one beep - the remote is in silent operation, two beeps the remote will beep when you hit your buttons, three beeps same as two, but the trolling motor will click about every second telling you it is on. Everytime you hold both buttons down, you will change modes

Quote:

---

Originally Posted by Dave C

Hold the top two buttons (increase and decrease speeds) for one second. If you hear one beep - the remote is in silent operation, two beeps the remote will beep when you hit your buttons, three beeps same as two, but the trolling motor will click about every second telling you it is on. Everytime you hold both buttons down, you will change modes

---

Thanks - did not know that!:D

Quote:

---

Originally Posted by Rapprunner

Thanks - did not know that!:D

---

Forgot to mention that you have to have your trolling motor plugged in for your remote to change modes.

Thats it Dave!! Just got back to the post!