Deck Boat Rigging

Any pics of rigged deck boat? I just bought a 22' Lowe and ready to start setting it up.


Sent from my iPhone using Crappie.com Fishing mobile app

Does it have a rail system? HiTek Stuff makes rod holders for rail slots.


Sent from my iPhone using Crappie.com

pics of the present layout would help us make suggestions

Quote:

---

Originally Posted by wannabe fisherman

pics of the present layout would help us make suggestions

---

Attachment 276043



Sent from my iPhone using Crappie.com Fishing mobile app

You might consider this : http://www.crappie.com/crappie/perso...ec-rod-holders if you don't have any objections to screwing the base plates down to the floor. But, before considering ANY brand of rod holder devices ... measure the most comfortable height & distance from your seats, taking into consideration your reach length to the rod handles and whether the placement of the holders will interfere with the raising/lowering of your trolling motor, or getting in/out of your seat, and distance from your knees.
As you can see in this picture of my setup, the left front mounting base is slightly farther from the inside edge of the bow than the right base is, and that was deliberately placed there so that I can raise/lower the trolling motor without having to take the rod holder out of the base when moving from spot to spot (under power of the big motor) : (pictured below)


The link I provided is for two 3rod Hi-tek holders, but as you can see from mine ... they do come in 4rod holder setups. just mentioned the 3rod setups because I don't know to what extent you intend to get into the use of multiple rod fishing methods. Another thing of note is that my setups have been "modified" by the addition of hard rubber knobs, in place of the adjustment bolts. This was done so that I can change the angle of the rods by hand, and not have to have a wrench or socket handy. (I've already dropped one socket overboard :Doh: )

I'm not recommending one brand over another ... just using "my" holder setup as an example. I did a "dry run" placement of the holders/bases, sitting in the seat to judge reach distance and best location for no interference with the trolling motor ... before the first screw hole was drilled. And FWIW ... my rod holders were purchased from another member, off the Personal Classifieds Forum of this site.

Pappy that was a very good reply.

That can't be a real boat Pappy! No crappie fisherman I ever knew had a boat that neat. It's got to have 2 dozen cranks all wadded up in a ball, used plastics ground into the carpet, and blood and slime all over from the last catfish battle. A couple I know of have tobacco spit added in for good measure.

Quote:

---

Originally Posted by mrdux

That can't be a real boat Pappy! No crappie fisherman I ever knew had a boat that neat. It's got to have 2 dozen cranks all wadded up in a ball, used plastics ground into the carpet, and blood and slime all over from the last catfish battle. A couple I know of have tobacco spit added in for good measure.

---

:Rofl ... yeah, well those white spots on the floor ARE catfish slime marks !! The only reason there ain't no blood stains is because I hadn't caught any Crappie on the cranks I was pulling at the time. I smoke my "bacca" so there's no spittle marks on the gunnel ... but, there are still some Coke spill stains on the carpet. :biggrin

Quote:

---

Originally Posted by CrappiePappy

You might consider this : http://www.crappie.com/crappie/perso...ec-rod-holders if you don't have any objections to screwing the base plates down to the floor. But, before considering ANY brand of rod holder devices ... measure the most comfortable height & distance from your seats, taking into consideration your reach length to the rod handles and whether the placement of the holders will interfere with the raising/lowering of your trolling motor, or getting in/out of your seat, and distance from your knees.
As you can see in this picture of my setup, the left front mounting base is slightly farther from the inside edge of the bow than the right base is, and that was deliberately placed there so that I can raise/lower the trolling motor without having to take the rod holder out of the base when moving from spot to spot (under power of the big motor) : (pictured below)


The link I provided is for two 3rod Hi-tek holders, but as you can see from mine ... they do come in 4rod holder setups. just mentioned the 3rod setups because I don't know to what extent you intend to get into the use of multiple rod fishing methods. Another thing of note is that my setups have been "modified" by the addition of hard rubber knobs, in place of the adjustment bolts. This was done so that I can change the angle of the rods by hand, and not have to have a wrench or socket handy. (I've already dropped one socket overboard :Doh: )

I'm not recommending one brand over another ... just using "my" holder setup as an example. I did a "dry run" placement of the holders/bases, sitting in the seat to judge reach distance and best location for no interference with the trolling motor ... before the first screw hole was drilled. And FWIW ... my rod holders were purchased from another member, off the Personal Classifieds Forum of this site.

---

dang pappy doin it with style lol

Thanks Pappy. That's good stuff. Nice rig!!


Sent from my iPhone using Crappie.com