Takin Her Home

Printable View

Show 40 post(s) from this thread on one page

08-28-2011, 11:47 AM
ScottV

That's a fine boat for sure BRM. Major and I could fish comfortably out of that one. Lol
08-28-2011, 07:38 PM
BigRiverMarine

Quote:

Originally Posted by gabowman

I know youre already loving 'er. I see a little fish slime. How'd she handle?

Ain't got the hours on her yet to really hammer down, but I've sold a bunch of em and they handle great especially in rough water. I did plane her out today with foot and a half white caps at Butla this afternoon, and she was like ridin on a cloud. Couldn't believe how smooth she was in the rough stuff. Could have been worse and she would have handled it with ease. I still gotta adjust my jack plate too. Blew out when I trimmed her up. Need to go down bout 1/2 inch or so and try her again.
08-28-2011, 07:44 PM
BigRiverMarine

Quote:

Originally Posted by E-Z Poleholder

You gotter going good, may as well paint 'MAJFLYBOY' on the side of her.

PM me your phone number. I need one of your rod racks with a twist.
08-28-2011, 07:49 PM
BigRiverMarine

Quote:

Originally Posted by ScottV

That's a fine boat for sure BRM. Major and I could fish comfortably out of that one. Lol

I gotta give ten demo rides in her. Next time y'all mosey up this way, we'll take for a test drive. ;-)
08-28-2011, 08:13 PM
Rees Guide

Quote:

Originally Posted by BigRiverMarine

I gotta give ten demo rides in her. Next time y'all mosey up this way, we'll take for a test drive. ;-)

Meet me at Grenada at daylight in the morning and we'll knock out one of them test runs!!Thumbs Up
08-28-2011, 08:36 PM
BigRiverMarine

Quote:

Originally Posted by Rees Guide

Meet me at Grenada at daylight in the morning and we'll knock out one of them test runs!!Thumbs Up

When I git er done, I'll take you up on that!!! I can't make it tomorrow, puttin an engine on a new Excel stick steer I sold.
08-28-2011, 09:05 PM
windstone

BRM, where you in that red boat with the red umbrella about one or so pretty close to that sail boat that went belly up?? if so, went right by you. nice lookin rig.
08-28-2011, 09:47 PM
Minnerman

Quote:

Originally Posted by BigRiverMarine

Ain't got the hours on her yet to really hammer down, but I've sold a bunch of em and they handle great especially in rough water. I did plane her out today with foot and a half white caps at Butla this afternoon, and she was like ridin on a cloud. Couldn't believe how smooth she was in the rough stuff. Could have been worse and she would have handled it with ease. I still gotta adjust my jack plate too. Blew out when I trimmed her up. Need to go down bout 1/2 inch or so and try her again.

I been tryin to tell folks how smooth they are but won't nobody believe me. You got my next one when I wear mine out.
08-28-2011, 09:53 PM
yikess

Quote:

Originally Posted by BigRiverMarine

Running a Power Tech 21 with a Jack Plate.

Let me know how it goes with the 21" stainless. Most of us try our very best to adjust everything we possibly can to get to 6000 rpms on a F115 with 21" but then reality sets in and we swallow a little pride and go on back to the store and get the 19" we should have gotten in the first place.Rofl

I know the Excel has the hyper-lift hull and the jackplate will certainly help but when you load an 18 foot boat with two grown men, full of fuel, full livewells and all your tournament gear in the dead of summer I seriously doubt you going the get the r's you want unless you add some nitrous which would be fun actually!!
08-29-2011, 08:33 AM
BigRiverMarine

Quote:

Originally Posted by windstone

BRM, where you in that red boat with the red umbrella about one or so pretty close to that sail boat that went belly up?? if so, went right by you. nice lookin rig.

Yea that was me and my fishin partner. Thanks!!

Show 40 post(s) from this thread on one page