Thanks Thanks:  0
HaHa HaHa:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: 78 or 79 evinrude 70hp wont stay running

  1. #1
    Join Date
    Jan 2014
    Location
    Kentucky
    Posts
    47
    Post Thanks / Like

    Default 78 or 79 evinrude 70hp wont stay running


    I have a 1978 or 79 Evinrude 70hp outboard, on the last trip to the lake it wasn't wanting to stay running unless I held the choke in. Once I let the choke go it was almost as if it was burning all the gas it had in the carb. then would die, After about a 1 1\2 hour it finally stayed running. I've never experienced this out this boat.
    "Give a man a fish, he eats for a day; teach a man to fish, he eats for a lifetime!"

  2. #2
    Barnacle Bill's Avatar
    Barnacle Bill is offline Super Mod and 2014 Crappie.com Man of the Year * Crappie.com Supporter
    Join Date
    Apr 2004
    Location
    Chesapeake, Va
    Posts
    20,251
    Post Thanks / Like

    Default

    I would say you either have some trash in the carbs or the fuel pump needs to be rebuilt. Start with the fuel pump as it is a cheap and easy job.
    Fair Winds and Following Seas

    Bill H. PTC USN Ret
    Chesapeake, Va


  3. #3
    Scrapper's Avatar
    Scrapper is offline Crappie Wall Hanger II - Moderator Mechanics forum
    Join Date
    Sep 2008
    Location
    Nashville AR
    Posts
    1,555
    Post Thanks / Like

    Default

    Check simple things first. Make sure the vent is venting. Check bulb and fuel line for cracks or bad check valve in bulb. Check VERY closely! Does it pump up firm before you start it? There is an inline filter on those engines...if you have never changed it...change it. Also check fuel pump...its has a small screen in it also. As Bill stated...they are very easy to change out...and cheap.

    Normally on engines that you have to push the choke in to run you have an air leak somewhere...carb to intake gasket etc...the air seeping in will lean it out...hence running with choke in which gets the air/fuel ratio to a point it will burn.....or and more times than not....a clogged jet in one or more carbs. Does it do it at idle only...all the time...or could you run it down the lake but not idle?? Does the same as an air leak...but the other direction...its getting too much air because the jets are not allowing the fuel to come through...so again...it leans out and you push choke in which gets the air/fuel ratio back to where it will burn.

    How old is the gas?? Have you ran any seafoam through it? Could of gotten some trash in a carb then it passed it...why it started running right later on in the day.

    If fuel lines, bulb, vent, filter, etc check out then I'm leaning to time to rebuild carbs.

    Have to choke it almost assures that its a fuel problem.
    "But if serving the Lord seems undesirable to you, then choose for yourselves this day whom you will serve, whether the gods your ancestors served beyond the Euphrates, or the gods of the Amorites, in whose land you are living. But as for me and my household, we will serve the Lord.” Joshua 25:15

  4. #4
    Join Date
    Jan 2014
    Location
    Kentucky
    Posts
    47
    Post Thanks / Like

    Default

    When I was on the lake it wouldn't get out of idle till after I played with it for a while idling half way down the lake then it just took off. The bulb never loss its prime, I got gas earlier that day, haven't tried seafoam yet. If the cost of fuel pump is cheap enough ill go ahead and change it and the filter just for safe measures. Thanks for the feedback, ill let y'all know how it goes.
    "Give a man a fish, he eats for a day; teach a man to fish, he eats for a lifetime!"

  5. #5
    Scrapper's Avatar
    Scrapper is offline Crappie Wall Hanger II - Moderator Mechanics forum
    Join Date
    Sep 2008
    Location
    Nashville AR
    Posts
    1,555
    Post Thanks / Like

    Default

    Really sounds like it passed some trash. Do you have a filter/water separator on it? Would be a good investment if not.
    "But if serving the Lord seems undesirable to you, then choose for yourselves this day whom you will serve, whether the gods your ancestors served beyond the Euphrates, or the gods of the Amorites, in whose land you are living. But as for me and my household, we will serve the Lord.” Joshua 25:15

  6. #6
    Join Date
    Jan 2014
    Location
    Kentucky
    Posts
    47
    Post Thanks / Like

    Default

    No sir, but I was just reading the seafoam thread and was looking at the filter/water separator someone posted and thought about buying one in the next few weeks when my budget allows, seemed like a good preventative action to take.
    "Give a man a fish, he eats for a day; teach a man to fish, he eats for a lifetime!"

  7. #7
    Scrapper's Avatar
    Scrapper is offline Crappie Wall Hanger II - Moderator Mechanics forum
    Join Date
    Sep 2008
    Location
    Nashville AR
    Posts
    1,555
    Post Thanks / Like

    Default

    I think I would rebuild the carbs also. Its not a hard process. Its time consuming...but not hard. That way you know everything is clean and ready to go. You will most likely not have any trouble again after that. check the screen in the fuel pump and the little inline filter also.

    How long did you run it after it started running right?? Did it do it anymore?
    "But if serving the Lord seems undesirable to you, then choose for yourselves this day whom you will serve, whether the gods your ancestors served beyond the Euphrates, or the gods of the Amorites, in whose land you are living. But as for me and my household, we will serve the Lord.” Joshua 25:15

  8. #8
    Join Date
    Jan 2014
    Location
    Kentucky
    Posts
    47
    Post Thanks / Like

    Default

    I ran it about 15 min. Then I cut it off, started and ran fine the rest the day till we went to put it on the trailer. I'm ordering a rebuild kit for fuel pump this week. I might just remove the carb. and soak it for a few days then clean it up.
    "Give a man a fish, he eats for a day; teach a man to fish, he eats for a lifetime!"

  9. #9
    Cray's Avatar
    Cray is offline Crappie.com 2019 Man of Year, Supermod & Moderator of the Mechanics Forum * Crappie.com Supporter
    Join Date
    Oct 2010
    Location
    Byhalia,Mississippi
    Posts
    17,343
    Post Thanks / Like

    Default

    If you can, pull the bowl off the carb and check for trash in the bottom of it.
    Proud Member of Team Geezer
    Charlie Weaver USN/ENC 1965-1979




  10. #10
    Scrapper's Avatar
    Scrapper is offline Crappie Wall Hanger II - Moderator Mechanics forum
    Join Date
    Sep 2008
    Location
    Nashville AR
    Posts
    1,555
    Post Thanks / Like

    Default

    +1 on what cray said. Simply soaking it without taking it apart will not get the trash out of it. You need to take it apart...soak it...then blow through all the orifices with air until clean. Then I would go ahead and put new jets (rebuild kit) on it.

    I would suggest berryman carb cleaner in the gallon. That is some great stuff...pricey but great.

    Another thing...if I remember right you have three carbs...if one is causing the problem. Lets say one is lean compared to the rest. That ALSO means that one is lean on oil. So that cylinder is not being lubricated as well as the other two. Running a multiple carb engine with one running lean is bad. And will eventually take that cylinder down. If it were me I would tear them all down, soak them overnight in berryman, blow them out and rebuild them.

    Just my two cents.
    "But if serving the Lord seems undesirable to you, then choose for yourselves this day whom you will serve, whether the gods your ancestors served beyond the Euphrates, or the gods of the Amorites, in whose land you are living. But as for me and my household, we will serve the Lord.” Joshua 25:15

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

BACK TO TOP